Cisco2610B的配置实例网络知识
【简介】感谢网友“lrrr”参与投稿，下面是小编给大家带来Cisco2610B的配置实例网络知识（共10篇），一起来阅读吧，希望对您有所帮助。
篇1：Cisco2610B的配置实例网络知识
Current configuration: ! version 11.3 service timestamps debug uptime service timestamps log uptime service password-encryption ! hostname 2610B ! enable password password ! username bluestudy password password no ip domain-lookup! ! inter
Current configuration:
!
version 11.3
service timestamps debug uptime
service timestamps log uptime
service password-encryption
!
hostname 2610B
!
enable password password
!
username bluestudy password password
no ip domain-lookup!
!
interface Ethe.net0/0
ip address 202.108.66.98 255.255.255.248
no shut
!
interface Serial0/0
ip address 202.108.8.1 255.255.255.252
no shut
!
interface Serial0/1
no ip address
shutdown
!
ip route 0.0.0.0 0.0.0.0 202.108.8.2
!
snmp-server community public RO
snmp-server community private RW
!
line con 0
line aux 0
line vty 0 4
login local
!
no scheduler allocate
end
原文转自：www.ltesting.net
篇2：Cisco3640Voip配置实例解析网络知识
下面是一个Cisco 3640的VOIP配置，对方的结构是台北和上海两地做VOIP,后接阿尔卡特的PBX,这是我亲手做的，里面有很多有注意的地方，与大家一起分享快乐！ 如有看不懂的地方请问我，还有我加的注解： Taipei#sh run Building configuration... Current config
下面是一个Cisco 3640的VOIP配置，对方的结构是台北和上海两地做VOIP,后接阿尔卡特的PBX,这是我亲手做的，里面有很多有注意的地方，与大家一起分享快乐！
如有看不懂的地方请问我，还有我加的注解：
Taipei#sh run
Building configuration...
Current configuration:
!
version 12.0
service timestamps debug uptime（设定Debug跟踪日志显示其时间）
service timestamps log uptime（设定看Log时显示其时间）
no service password-encryption（口令不加密）
!
hostname Taipei（主机名）
!
enable secret 5 $1$R.66$z.BUjhNsJcIr8KCcS9uxG.
!
!
!
!
!
voice-card 1（定义语音卡1）
!
voice-card 3（定义语音卡3）
!
ip su.net-zero
no ip domain-lookup
!
isdn voice-call-failure 0
!
!
!
!
controller E1 1/0（配置 E1语音卡）
framing NO-CRC4
ds0-group 0 timeslots 1-15,17-31 type e&m-wink-start（定义语音卡的类型为E&M卡）
cas-custom 0
!
controller E1 3/0（配置 E1语音卡）
framing NO-CRC4
ds0-group 0 timeslots 1-15,17-31 type e&m-wink-start（定义语音卡的类型为E&M卡）
cas-custom 0
!
!
!
interface BRI0/0
no ip address
no ip directed-broadcast
shutdown
isdn guard-timer 0 on-expiry aclearcase/“ target=”_blank“ >ccept
!
interface FastEthernet0/0
no ip address
no ip directed-broadcast
shutdown
duplex auto
speed auto
!
interface Serial0/0
description ”Link to MainLand_ShangHai by NCIC lease line“
ip address 192.168.1.1 255.255.255.252
no ip directed-broadcast
no ip mroute-cache
no fair-queue
!
interface Serial0/1
no ip address
no ip directed-broadcast
shutdown
clockrate 000
!
ip classless
no ip http server
!
!
voice-port 1/0:0（配置模拟语音端口）
compand-type a-law
!
voice-port 3/0:0（配置模拟语音端口）
compand-type a-law
!
dial-peer voice 1 voip （定义拨号对等体到语音）
destination-pattern +445...（为拨号对等体分配电话号码，其中.为通配符）
session target ipv4:192.168.1.2（定义Voip路由，为对端的IP地址）
req-qos guaranteed-delay （语音数据流RVSP的保证，其中Guaranteed-dealy可用于保证整个网络的延时）
ip precedence 5（IP优先级，5为关键）
!
dial-peer voice 2 pots（定义拨号对等体到语音物理端口）
destination-pattern +3...（定义电话话码以3开头的）
port 1/0:0（定义语音端口）
!
dial-peer voice 3 pots（定义拨号对等体到语音物理端口）
destination-pattern +3...（定义电话话码以3开头的）
port 3/0:0（定义语音端口）
!
!
line con 0（设定登陆）
transport input none
line aux 0
line vty 0 4（允许用Telnet）
password cisco（口令为Cisco)
login
!
end
Taipei#
上海一方的3640配置
ShangHai#sh run
Building configuration...
Current configuration:
!
version 12.0
service timestamps debug uptime
service timestamps log uptime
no service password-encryption
!
hostname ShangHai
!
enable secret 5 $1$dB/c$tnrMU9IxFCJdix5ssHAdH/
!
!
!
!
!
voice-card 1
!
voice-card 2
!
ip subnet-zero
no ip domain-lookup
!
isdn voice-call-failure 0
!
!
!
!
controller E1 1/0
framing NO-CRC4
ds0-group 0 timeslots 1-15,17-31 type e&m-immediate-start
cas-custom 0
!
controller E1 2/0
framing N
ds0-group 0 timeslots 1-15,17-31 type e&m-immediate-start
cas-custom 0
!
!
!
interface BRI0/0
no ip address
no ip directed-broadcast
encapsulation ppp
isdn guard-timer 0 on-expiry accept
ppp multilink
!
interface FastEthernet0/0
no ip address
no ip directed-broadcast
shutdown
duplex auto
speed auto
!
interface Serial0/0
no ip address
no ip directed-broadcast
no ip mroute-cache
shutdown
no fair-queue
clockrate 2000000
!
interface Serial0/1
ip address 192.168.1.2 255.255.255.252
no ip directed-broadcast
!
ip classless
!
no ip http server
!
!
voice-port 1/0:0
compand-type a-law
!
voice-port 2/0:0
compand-type a-law
!
dial-peer voice 20 voip
destination-pattern +3...
session target ipv4:192.168.1.1
req-qos guaranteed-delay
ip precedence 5
!
dial-peer voice 10 pots
destination-pattern +448...
port 1/0:0
!
dial-peer voice 30 voip
destination-pattern +4...
session target ipv4:192.168.1.1
req-qos guaranteed-delay
ip precedence 5
!
dial-peer voice 40 pots
destination-pattern +449...
port 2/0:0
!
!
line con 0
transport input none
line aux 0
line vty 0 4
password cisco
login
!
end
ShangHai#
原文转自：www.ltesting.net
篇3：Cisco2610A的配置实例网络知识
Current configuration: ! version 11.3 service timestamps debug uptime service timestamps log uptime service password-encryption ! hostname 2610A ! enable password password ! username bluestudy password password no ip domain-lookup! ! inter
Current configuration:
!
version 11.3
service timestamps debug uptime
service timestamps log uptime
service password-encryption
!
hostname 2610A
!
enable password password
!
username bluestudy password password
no ip domain-lookup!
!
interface Ethe.net0/0
ip address 192.168.0.2 255.255.255.252
no shut
!
interface Serial0/0
ip address 192.168.0.5 255.255.255.252
no shut
!
interface Serial0/1
no ip address
shutdown
!
ip route 0.0.0.0 0.0.0.0 192.168.0.1
ip route 192.168.2.0 255.255.255.0 192.168.0.6
!
snmp-server community public RO
snmp-server community private RW
!
line con 0
line aux 0
line vty 0 4
login local
!
no scheduler allocate
end
原文转自：www.ltesting.net
篇4：Cisco2610C的配置实例网络知识
version 11.2 service udp-small-servers service tcp-small-servers ! hostname 2610C ! enable secret cisco ! ip su .net -zero no ip domain-lookup ! ip address-pool local isdn switch-type basic-net3 interface Ethernet0 ip address 10.2.0.11 255
version 11.2
service udp-small-servers
service tcp-small-servers
!
hostname 2610C
!
enable secret cisco
!
ip su.net-zero
no ip domain-lookup
!
ip address-pool local
isdn switch-type basic-net3
interface Ethernet0
ip address 10.2.0.11 255.255.0.0
!
interface Serial0
no ip address
encapsulation frame-relay
frame-relay lmi-type ansi
!
interface Serial0.1 point-to-point
description Frame. Relay to bluestudy1
ip unnumbered Ethernet0
frame-relay interface-dlci 10
!
interface Serial0.2 point-to-point
description Frame. Relay to bluestudy2
ip unnumbered Ethernet0
frame-relay interface-dlci 11
!
interface BRI1/0
no ip address
shutdown
isdn switch-type basic-net3
!
interface BRI1/1
ip address 192.168.3.1 255.255.255.240
encapsulation ppp
timeout absolute 60 0
dialer idle-timeout 3600
dialer-group 1
isdn switch-type basic-net3
peer default ip address pool default
ppp authentication chap pap callin
!
interface BRI1/2
no ip address
encapsulation ppp
shutdown
isdn switch-type basic-net3
!
interface BRI1/3
no ip address
encapsulation ppp
shutdown
isdn switch-type basic-net3
no peer default ip address
!
ip local pool default 192.168.3.3 192.168.3.14
ip http server
ip classless
ip route 192.168.5.0 255.255.255.0 serial0.1
ip route 192.168.4.0 255.255.255.0 serial0.2
ip route 0.0.0.0 0.0.0.0 10.2.0.1
!
aclearcase/” target=“_blank” >ccess-list 1 permit any
dialer-list 1 protocol ip list 1
line con 0
password console
login
line aux 0
line vty 0 4
password telnet
login
!
end
原文转自：www.ltesting.net
篇5：Cisco3550交换机配置DHCP服务器实例网络知识
网络 环境：一台3550E MI 交换机，划分三个vlan,vlan2 为 服务器 所在网络，命名为server,IP地址段 为192.168.2.0,子网掩码:255.255.255.0,网关:192.168.2.1,域服务器为 windows advance server,同时兼作DNS服务器，IP地址为192.168.2.10,vlan3为客户机
网络环境：一台3550EMI交换机，划分三个vlan,vlan2 为服务器所在网络，命名为server,IP地址段
为192.168.2.0,子网掩码:255.255.255.0,网关:192.168.2.1,域服务器为windows2000 advance server,同时兼作DNS服务器，IP地址为192.168.2.10,vlan3为客户机1所在网络，IP地址段为192.168.3.0,子网掩码:255.255.255.0,网关:192.168.3.1命名为work01,vlan4为客户机2所在网络,命名为work02,IP地址段为192.168.4.0,子网掩码:255.255.255.0,网关:192.168.4.1,3550作DHCP服务器,端口1-8划到VLAN 2，端口9-16划分到VLAN 3,端口17-24划分到VLAN 4.
DHCP服务器实现功能:
各VLAN保留2-10的IP地址不分配置,例如:192.168.2.0的网段,保留192.168.2.2至192.168.2.10的IP地
址段不分配.
安全要求:
VLAN 3和VLAN 4 不允许互相访问,但都可以访问服务器所在的VLAN 2,
默认访问控制列表的规则是拒绝所有包，
配置命令及步骤如下：
第一步：创建VLAN：
Switch>en
Switch#Vlan Database
Switch(Vlan)>Vlan 2 Name server
Switch(Vlan)>Vlan 3 Name work01
Switch(vlan)>Vlan 4 Name work02
第二步：设置VLAN IP地址：
Switch#Config T
Switch(Config)>Int Vlan 2
Switch(Config-vlan)Ip Address 192.168.2.1 255.255.255.0
Switch(Config-vlan)No Shut
Switch(Config-vlan)>Int Vlan 3
Switch(Config-vlan)Ip Address 192.168.3.1 255.255.255.0
Switch(Config-vlan)No Shut
Switch(Config-vlan)>Int Vlan 4
Switch(Config-vlan)Ip Address 192.168.4.1 255.255.255.0
Switch(Config-vlan)No Shut
Switch(Config-vlan)Exit
/*注意：由于此时没有将端口分配置到VLAN2，3，4，所以各VLAN会DOWN掉，待将端口分配到各VLAN后，VLAN会起来*/
第三步：设置端口全局参数
Switch(Config)Interface Range Fa 0/1 - 24
Switch(Config-if-range)Switchport Mode Aclearcase/“ target=”_blank“ >ccess
Switch(Config-if-range)Spanning-tree Portfast
第四步：将端口添加到VLAN2，3，4中
/*将端口1-8添加到VLAN 2*/
Switch(Config)Interface Range Fa 0/1 - 8
Switch(Config-if-range)Switchport Access Vlan 2
/*将端口9-16添加到VLAN 3*/
Switch(Config)Interface Range Fa 0/9 - 16
Switch(Config-if-range)Switchport Access Vlan 3
/*将端口17-24添加到VLAN 4*/
Switch(Config)Interface Range Fa 0/17 - 24
Switch(Config-if-range)Switchport Access Vlan 4
Switch(Config-if-range)Exit
/*经过这一步后，各VLAN会起来*/
第五步：配置3550作为DHCP服务器
/*VLAN 2可用地址池和相应参数的配置,有几个VLAN要设几个地址池*/
Switch(Config)Ip Dhcp Pool Test01
/*设置可分配的子网*/
Switch(Config-pool)Network 192.168.2.0 255.255.255.0
/*设置DNS服务器*/
Switch(Config-pool)Dns-server 192.168.2.10
/*设置该子网的网关*/
Switch(Config-pool)Default-router 192.168.2.1
/*配置VLAN 3所用的地址池和相应参数*/
Switch(Config)Ip Dhcp Pool Test02
Switch(Config-pool)Network 192.168.3.0 255.255.255.0
Switch(Config-pool)Dns-server 192.168.2.10
Switch(Config-pool)Default-router 192.168.3.1
/*配置VLAN 4所用的地址池和相应参数*/
Switch(Config)Ip Dhcp Pool Test03
Switch(Config-pool)Network 192.168.4.0 255.255.255.0
Switch(Config-pool)Dns-server 192.168.2.10
Switch(Config-pool)Default-router 192.168.4.1
第六步:设置DHCP保留不分配的地址
Switch(Config)Ip Dhcp Excluded-address 192.168.2.2 192.168.2.10
Switch(Config)Ip Dhcp Excluded-address 192.168.3.2 192.168.3.10
Switch(Config)Ip Dhcp Excluded-address 192.168.4.2 192.168.4.10
第七步:启用路由
/*路由启用后,各VLAN间主机可互相访问*/
Switch(Config)Ip Routing
第八步:配置访问控制列表
Switch(Config)access-list 103 permit ip 192.168.2.0 0.0.0.255 192.168.3.0 0.0.0.255
Switch(Config)access-list 103 permit ip 192.168.3.0 0.0.0.255 192.168.2.0 0.0.0.255
Switch(Config)access-list 103 permit udp any any eq bootpc
Switch(Config)access-list 103 permit udp any any eq tftp
Switch(Config)access-list 103 permit udp any eq bootpc any
Switch(Config)access-list 103 permit udp any eq tftp any
Switch(Config)access-list 104 permit ip 192.168.2.0 0.0.0.255 192.168.4.0 0.0.0.255
Switch(Config)access-list 104 permit ip 192.168.4.0 0.0.0.255 192.168.2.0 0.0.0.255
Switch(Config)access-list 104 permit udp any eq tftp any
Switch(Config)access-list 104 permit udp any eq bootpc any
Switch(Config)access-list 104 permit udp any eq bootpc any
Switch(Config)access-list 104 permit udp any eq tftp any
第九步:应用访问控制列表
/*将访问控制列表应用到VLAN 3和VLAN 4,VLAN 2不需要*/
Switch(Config)Int Vlan 3
Switch(Config-vlan)ip access-group 103 out
Switch(Config-vlan)Int Vlan 4
Switch(Config-vlan)ip access-group 104 out
第十步：结束并保存配置
Switch(Config-vlan)End
Switch#Copy Run Start
原文转自：www.ltesting.net
篇6：Cisco 6509为主网络配置实例
配置上完全没有问题，已经运行近半年了，主旨是大家能共同学习，用实践来巩固自己学习的成果。有什么问题尽管跟帖，相信大家一起讨论，一定能解决一切问题。
一、Catalyst 6509交换机配置方案
1.1、配置6509二层交换
Console>（enable） set system name bg-sw-01 /设备名称
Bg-sw-01>（enable ） set password
Enter old password:
Enter new password: test /设备口令
Retype new password: test
Bg-sw-01>（enable） set enablepass
Enter old password:
Enter new password: test /设备口令
Retype new password: test
Bg-sw-01>（enable） set banner motd % Welcome to the c6509 in the office % /提示文本
Bg-sw-01>（enable） set interface sc0 10.234.180.21 255.255.255.0 /设置管理接口 #sh int
Bg-sw-01>（enable） set ip route default 10.234.180.234 /设置默认网关 #sh ip route
Bg-sw-01>（enable） set vtp mode server /设置VTP模式 #sh vtp domain
Bg-sw-01>（enable） set vtp domain Core_Net /设置VTP域名
Bg-sw-01>（enable） set vlan 31 name ZhongSanLu /创建VLAN #sh vlan
Bg-sw-01>（enable） set vlan 32 name YiYang
Bg-sw-01>（enable） set vlan 33 name JianXiu
Bg-sw-01>（enable） set vlan 34 name RaoDian
Bg-sw-01>（enable） set vlan 35 name JinSanLou
Bg-sw-01>（enable） set vlan 36 name WuZi
Bg-sw-01>（enable） set port channel 1/1-2 on /设置Channel #sh port channel
Bg-sw-01>（enable） set trunk 1/1 on dot1q 1-1005
Bg-sw-01>（enable） set trunk 2/2 on dot1q 1-1005 /设置trunk口 #sh trunk #
Bg-sw-01>（enable） set trunk 2/3 on dot1q 1-1005
Bg-sw-01>（enable） set trunk 2/4 on dot1q 1-1005
Bg-sw-01>（enable） set trunk 2/5 on dot1q 1-1005
Bg-sw-01>（enable） set trunk 2/6 on dot1q 1-1005
Bg-sw-01>（enable） set trunk 2/7 on dot1q 1-1005
Bg-sw-01>（enable） set spantree root 1-40 dia 4 /设为spantree的根 #sh spantree
Bg-sw-01>（enable） set spantree portfast 1/1-2 enable /设spantree端口快速启用
Bg-sw-01>（enable） set spantree portfast 2/1-8 enable
Bg-sw-01>（enable） set spantree uplinkfast enable /设spantree端口快速切换
Bg-sw-01>（enable） set spantree backbonefast enable /设spantree端口快速定位根
1.2、配置路由
Console>（enable） session 15 /进入路由子卡
Router（config）# hostname c6509-msfc /设备名
c6509-msfc （config）# enable password test /设口令
c6509-msfc （config）# enable secret test
C6509-msfc（config）# banner motd % Welcome to the c6509-msfc in the Office % /设提示文本
c6509-msfc （config）# line vty 0 4 / 进入VTY模式
c6509-msfc （config-line）#login / 登入提示
c6509-msfc （config-line）#password test / 设用户级口令
c6509-msfc （config-line）# end
C6509-msfc#configure terminal / 进入全局模式
Enter configuration commands, one per line. End with CNTL/Z.
C6509-msfc（config）# interface vlan 1 /进入虚子接口
C6509-msfc（config-if）# ip address 10.234.180.232 255.255.255.0 /加ip地址
C6509-msfc（config-if）# no shutdown /开启端口
C6509-msfc（config-if）# standby 1 ip 10.234.180.234 /建HSRP组并设虚IP地址
C6509-msfc（config-if）# standby 1 priority 110 /设优先级
C6509-msfc（config-if）# standby 1 preempt /设切换许可
C6509-msfc（config-if）# interface vlan 31
C6509-msfc（config-if）# ip address 10.234.181.60 255.255.255.192
C6509-msfc（config-if）# no shutdown
C6509-msfc（config-if）# standby 31 ip 10.234.181.62
C6509-msfc（config-if）# standby 31 priority 110
C6509-msfc（config-if）# standby 31 preempt
C6509-msfc（config-if）# interfacevlan 32
C6509-msfc（config-if）# ip address 10.234.181.124 255.255.255.192
C6509-msfc（config-if）# no shutdown
C6509-msfc（config-if）# standby 32 ip 10.234.181.126
C6509-msfc（config-if）# standby 32 priority 110
C6509-msfc（config-if）# standby 32 preempt
C6509-msfc（config-if）# interface vlan 33
C6509-msfc（config-if）# ip address 10.234.181.188 255.255.255.192
C6509-msfc（config-if）# no shutdown
C6509-msfc（config-if）# standby 33 ip 10.234.181.190
C6509-msfc（config-if）# standby 33 priority 110
C6509-msfc（config-if）# standby 33 preempt
C6509-msfc（config-if）# interface vlan 34
C6509-msfc（config-if）# ip address 10.234.181.220 255.255.255.224
C6509-msfc（config-if）# no shutdown
C6509-msfc（config-if）# standby 34 ip 10.234.181.222
C6509-msfc（config-if）# standby 34 priority 110
C6509-msfc（config-if）# standby 34 preempt
C6509-msfc（config-if）# interface vlan 35
C6509-msfc（config-if）# ip address 10.234.181.254 252.255.255.224
C6509-msfc（config-if）# no shutdown
C6509-msfc（config-if）# standby 35 ip 10.234.181.254
C6509-msfc（config-if）# standby 35 priority 110
C6509-msfc（config-if）# standby 35 preempt
C6509-msfc（config-if）# interface vlan 36
C6509-msfc（config-if）# ip address 10.234.182.28 255.255.255.224
C6509-msfc（config-if）# no shutdown
C6509-msfc（config-if）# standby 36 ip 10.234.182.30
C6509-msfc（config-if）# standby 36 priority 110
C6509-msfc（config-if）# standby 36 preempt
C6509-msfc（config-if）# exit
篇7：CiscoHSRP的配置网络知识
version 12.0 service timestamps debug uptime service timestamps log uptime no service password-encryption ! hostname r1 ! enable password cisco ! ip su .net -zero ! ! ! ! interface Ethernet0 ip address 136.147.107.101 255.255.0.0 no ip red
version 12.0
service timestamps debug uptime
service timestamps log uptime
no service password-encryption
!
hostname r1
!
enable password cisco
!
ip su.net-zero
!
!
!
!
interface Ethernet0
ip address 136.147.107.101 255.255.0.0
no ip redirects
no ip directed-broadcast
standby 150 timers 5 15 /* 定义150组5秒交换一次hello信息，15秒没收到
hello信息就开始切换 */
standby 150 priority 110 /* 定义150组的主路由器权值，值越大，为主路由
器希望越大 */
standby 150 preempt /* enable 150组的hsrp抢占功能 */
standby 150 authentication cisco /* 设置150组的router身份验证串 */
standby 150 ip 136.147.107.100 /* 定义150组的浮动地址，也是这台router
连接的网络的网关 */
standby 150 track Ethernet0 /* 定义监控的端口 */
!
interface Serial0
no ip address
no ip directed-broadcast
no ip mroute-cache
shutdown
no fair-queue
!
ip classless
!
!
line con 0
transport input none
line 1 16
line aux 0
line vty 0 4
password cisco
login
!
end
原文转自：www.ltesting.net
篇8：4006s2配置清单网络知识
作3层交换 Enter password: ZX_WS4006_1>(enable) sh mod Mod Slot Ports Module-Type Model Sub Status --- ---- ----- ------------------------- ------------------- --- -------- 1 1 2 1000BaseX Supervisor WS-X4013 no ok 3 3 6 1000BaseX Ethernet
作3层交换
Enter password:
ZX_WS4006_1>(enable) sh mod
Mod Slot Ports Module-Type Model Sub Status
--- ---- ----- ------------------------- ------------------- --- --------
1 1 2 1000BaseX Supervisor WS-X4013 no ok
3 3 6 1000BaseX Ethernet WS-X4306 no ok
4 4 34 Router Switch Card WS-X4232-L3 no ok
Mod Module-Name Serial-Num
--- -------------------- --------------------
1 JAE060906GZ
3 JAE04470A10
4 JAB052105F2
Mod MAC-Address(es) Hw Fw Sw
--- -------------------------------------- ------ ---------- -----------------
1 00-08-e3-86-06-00 to 00-08-e3-86-09-ff 3.2 5.4(1) 6.3(1)
3 00-04-27-55-93-2c to 00-04-27-55-93-31 2.0
4 00-04-9a-50-16-4c to 00-04-9a-50-16-6d 1.7 12.0(7)W5( 12.0(10)W5(18f)
ZX_WS4006_1>(enable) sh config
This command shows non-default configurations only.
Use 'show config all' to show both default and non-default configurations.
.............
..................
..................
....................
..
begin
!
# ***** NON-DEFAULT CONFIGURATION *****
!
!
#time: Tue Mar 18 , 23:11:06
!
#version 6.3(1)
!
!
#system web interface version(s)
set password $2$ZtNY$yuqPHi7CpjwCs0blr9mxG0
set enablepass $2$rY7u$b9D5DEa661dt46OwWq5ts/
!
#test
set test diaglevel minimal
!
#system
set system name ZX_WS4006_1
set system contact Center-sw
!
#frame. distribution method
set port channel all distribution mac both
!
#vtp
set vtp domain cs1yhis
set vlan 1 name default type ethernet mtu 1500 said 100001 state active
set vlan 2 name JiGuan type ethernet mtu 1500 said 100002 state active
set vlan 3 name YeWu type ethernet mtu 1500 said 100003 state active
set vlan 4 name XXZX type ethernet mtu 1500 said 100004 state active
set vlan 100 name yibao type ethernet mtu 1500 said 100100 state active
set vlan 1002 name fddi-default type fddi mtu 1500 said 101002 state active
set vlan 1004 name fddinet-default type fddinet mtu 1500 said 101004 state activ
e stp ieee
set vlan 1005 name trnet-default type trbrf mtu 1500 said 101005 state active st
p ibm
set vlan 5-20
set vlan 1003 name token-ring-default type trcrf mtu 1500 said 101003 state acti
ve mode srb aremaxhop 0 stemaxhop 0 backupcrf off
!
#ip
set interface sc0 1 192.168.1.250/255.255.255.0 192.168.1.255
set interface sl0 192.168.168.1 255.255.255.0
set interface sl0 down
set interface me1 192.0.2.1 255.255.255.0 192.0.2.255
set ip route 0.0.0.0/0.0.0.0 192.168.1.254
!
#dns
set ip dns server 202.103.96.68 primary
set ip dns server 202.103.4.238
!
#syslog
set logging level cops 2 default
!
#set boot command
set boot config-register 0x2
set boot system flash bootflash:cat4000.6-3-1.bin
set boot system flash bootflash:cat4000.5-5-8.bin
!
#mls
set mls nde disable
!
#port channel
set port channel 4/1-2 25
!
#http configuration
set ip http server enable
!
#module 1 : 2-port 1000BaseX Supervisor
set udld enable 1/1-2
!
#module 2 empty
!
#module 3 : 6-port 1000BaseX Ethernet
set udld enable 3/6
set trunk 3/3 on dot1q 1-1005
set trunk 3/4 on dot1q 1-1005
set trunk 3/5 on dot1q 1-1005
set trunk 3/6 on dot1q 1-1005
!
#module 4 : 34-port Router Switch Card
set trunk 4/1 nonegotiate dot1q 1-1005
set trunk 4/2 nonegotiate dot1q 1-1005
set port channel 4/1-2 mode on
!
#module 5 empty
!
#module 6 empty
end
ZX_WS4006_1>(enable)
ZX_WS4006_1>(enable) sess 3
Feature not supported on Module 3.
ZX_WS4006_1>(enable) sess 4
Trying IntlgLineCard-4...
Connected to IntlgLineCard-4.
Escape character is '^]'.
User Aclearcase/” target=“_blank” >ccess Verification
Password:
VLAN-gw>en
Password:
VLAN-gw#sh run
Building configuration...
Current configuration:
!
version 12.0
no service pad
service timestamps debug uptime
service timestamps log uptime
service password-encryption
!
hostname VLAN-gw
!
enable secret 5 $1$j6xO$q2wF0qaki76qo6hr3bYlt.
enable password 7 070E25414707
!
ip subnet-zero
no ip domain-lookup
ip name-server 202.103.96.68
ip name-server 202.103.100.100
!
!
!
interface Port-channel1
description This is interface is configured for routing with native vlan 1 to 4
no ip address
no ip redirects
no ip directed-broadcast
hold-queue 300 in
!
interface Port-channel1.1
encapsulation dot1Q 1 native
ip address 192.1.1.254 255.255.255.0 secondary
ip address 192.168.1.254 255.255.255.0
no ip redirects
no ip directed-broadcast
!
interface Port-channel1.2
description This interface is connected to vlan 2 which is connected to vlan
encapsulation dot1Q 2
ip address 192.168.2.254 255.255.255.0
no ip redirects
no ip directed-broadcast
!
interface Port-channel1.3
description This interface is connected to vlan 3 which is connected to vlan 3
encapsulation dot1Q 3
ip address 192.168.3.254 255.255.255.0
no ip redirects
no ip directed-broadcast
!
interface FastEthernet1
description This is the out of band interface that you can use for management
ip address 172.168.1.1 255.255.255.0
no ip directed-broadcast
!
interface GigabitEthernet1
no ip address
no ip directed-broadcast
!
interface GigabitEthernet2
no ip address<
原文转自：www.ltesting.net
篇9：3550emi配置DHCPSERVER！网络知识
相关配置命令： config)#ip dhcp pool [地址池名] (config)#ip dhcp excluded-address [不分配的地址] (dhcp-config) .net work [要分配的地址] [掩码] (dhcp-config)#lease [租约] (dhcp-config)#default-router [默认网关] (dhcp-config)#dns-server[dns
相关配置命令：
config)#ip dhcp pool [地址池名]
(config)#ip dhcp excluded-address [不分配的地址]
(dhcp-config).network [要分配的地址] [掩码]
(dhcp-config)#lease [租约]
(dhcp-config)#default-router [默认网关]
(dhcp-config)#dns-server[dns服务器]
然后要对自动获取地址的vlan 进行设置
(config)#ip helper-address [交换机地址]
再将端口划分到vlan 里
show config:
ip dhcp excluded-address 10.0.199.200 10.0.199.254
!
ip dhcp pool test
network 10.0.199.0 255.255.255.0
default-router 10.0.199.1
dns-server 10.0.199.252
lease 0 0 5
nterface Vlan199
ip address 10.0.199.1 255.255.255.0
ip helper-address 10.0.1.1
原文转自：www.ltesting.net
篇10：SAMSUNGSR4901ISDNROUTER配置方法网络知识
IP(static)/PPP/Security(Out)/Unnumbered/NAT(PAT) PC1 -->SR -->ISDN -->ISP | PC2 -----+ PC1 : Ethernet : 214.100.10.2 255.255.255.0 Gateway : 214.100.10.1 PC2 : Ethernet : 214.100.10.3 255.255.255.0 Gateway : 214.100.10.1 SR : Ethernet :
IP(static)/PPP/Security(Out)/Unnumbered/NAT(PAT)
PC1 -->SR -->ISDN -->ISP
|
PC2 -----+
PC1 :
Ethernet : 214.100.10.2 255.255.255.0
Gateway : 214.100.10.1
PC2 :
Ethernet : 214.100.10.3 255.255.255.0
Gateway : 214.100.10.1
SR :
Ethernet : 214.100.10.1 255.255.255.0
Serial : 0.0.0.0 0.0.0.0
Outgoing ID : son
Outgoing Password : son-out
NAT Global IP : 123.12.12.1 255.255.255.0
First, We are set the NAT Global IP with temporary IP (123.12.
12.1).
When we are connect to ISP, ISP send to me a ONE IP Address dy
namically.
That IP Address will be copy in NAT Global IP automatically.
(123.12.12.1 ->Delete)
ISP Tel No : 3448-8897
====================================================================
SR's configuration
1. Special Link/WAN/PPP over ISDN (for Serial IP)
Channel Channel-1
Channel Status Up
ISDN Dest Addr 34488897
ISDN Dest Sub Addr (blank)
IP Configuration
Admin Status Up
IP Address 0.0.0.0
Network Mask 0.0.0.0
Routing Protocol None
IPX Configuration
IPX Network Number (blank)
Admin Status Down
Oper Status (blank)
Bridge Configuration
Base Bridge Status Down
STP Status Down
2. Special Link/IP Routing/Static Route (for static table)
Destination Address0.0.0.0 214
.100.10.1
Subnet Mask 0.0.0.0 255
.255.255.0
Channel Channel-1 Ethernet
X.25 Virtual Circuit number 0 0
Address of the next hop(Gateway) 0.0.0.0 0.0.0.
0
Metric associated with the route 1 1
Static Route status Enable Ena
ble
3. Special Link/PPP/Router Security (for Outgoing)
Router Name : son
Outgoing Password : son-out
4. Features/NAT (for NAT)
NAT Table
Global IP address : 123.12.12.1
Subnet Mask: 255.255.255.0
NAT entry status : Create
Net Map list. : 214.100.10.0,255.255.255.0;
Enable NAT in the router : Yes
NAT Global
NAT port translation required : Yes
--Be careful--
Until Version 1.4 -->
Net Map list : 214.100.10.2,255.255.255.0,*-1300;214.100.10.3,
255.255.255.0,*-1310;
From Version 1.4.1 -->
Net Map list : 214.100.10.0,255.255.255.0;
原文转自：www.ltesting.net
